Leading 10 usual forklift crashes ， forklift procedure must focus on these matters ！.

Do not undervalue the forklift at work. If the procedure is not good, there will be serious accidents in mins, and there are lots of mishaps involving forklifts.

Situation 1: The forklift freight obstructed the chauffeur's view, and the person ahead might not be discovered, causing a moving mishap.
Instance 2: In order to maintain the balance of the forklift when lifting heavy items, the employees utilized their body weight as the weight, which almost created casualties.
Instance 3: The width of the forklift cargo goes beyond the allowed width of the route and holds on the roadside shelf, which almost creates an mishap.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift driver did not notice the pedestrian, and the pedestrian did not discover the forklift.
Situation 6: The forklift lifts the employees illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Instance 7: The forklift vehicle driver did not put on a safety belt and fell from the vehicle when it rolled over and was squashed.
Forklift operation must focus on these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after verifying that there are no obstacles that impede the safety and security of driving, honk the horn first and after that begin.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be risk-free prior to starting.
3. When the forklift begins with a lots, the chauffeur should first validate that the tons is secure and trusted.
4. The beginning has to be sluggish and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole ought to be tilted backward. .
2. Do not lift the fork too high when driving. When getting in and leaving the work site or while driving, be careful that there will be no barriers overhead. When the lots is taking a trip, the fork should not be increased expensive, which will impact the stability of the forklift. .
3. After discharging, the fork ought to be decreased to the typical driving position before driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal needs to be released initially. High-speed doglegs are forbidden. High-speed sharp turns will certainly trigger the vehicle to lose side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to turn off the flame and slide, and it is prohibited to brake suddenly while driving with loads unless there are unique scenarios.
6. When the forklift is running, it needs to obey the website traffic rules in the factory and should keep a particular safety distance from the vehicle in front. .
7. When the forklift is running, the tons should remain in the lowest position that does not impede the driving, and the gantry should be properly slanted back. The tons shall not be increased except when piling or filling. .
8. The elevation of the lots need to not block the vehicle driver's sight. In special conditions, when the thing affects the forward vision, drive at a low speed when turning around.
9. It is prohibited to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a low rate when going into the manufacturing workshop area. .
11. When the forklift is raised, raised or driven, it is restricted for workers to depend on the fork to hold things and play a balancing duty. .
12. If problems are discovered, they will be fixed and reported in a prompt fashion, and they will never operate with ailments or conceal them.

packing and dumping.
1. When fork-loading items, the distance in between both forks should be adjusted as needed to make the lots of both forks well balanced and not skewed, and one side of the thing must protest the shelf. .
2. It is forbidden to collaborate with a single fork or make use of a fork top or pull. In unique conditions, security warning signs have to be established to remind bordering pedestrians. .
3. In the process of loading and unloading products, the forklift must be braked with the brake. .
4. The rate of the automobile ought to be slow-moving and steady. Be careful not to roll the wheels on the dunnage, Stand-on Electric Pallet Stacker so as not to stretch the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it should be kept in mind that the fork tip must not touch other items or objects. The lots must be stabilized with marginal back tilt of the gantry to make sure that the load does not move backwards. The mast can be slanted ahead somewhat when the lots is reduced to allow for very easy placement of the tons and extraction of the forks. .
6. It is forbidden to fork goods at broadband and ram tough items with the fork head. .
7. When the forklift is working, it is prohibited for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Straining is banned, and it is forbidden to use forks to lift workers to take part in high-altitude procedures to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to utilize forks to choose, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of sight and does not go beyond 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming ought to not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel lug the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not enabled to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not allowed under the list below conditions.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the very same size Stand-on Electric Pallet Stacker as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844